12v 19v regulator trabalhos

...dc-dc, miscelâneas. Programei pela IDE ARDUINO. Integrei com supervisório remoto em nuvem que recebe os dados via post HTTP. Montei em uma placa padrão dentro de uma caixa de plástico. - Tensão de alimentação 12Vcc +- 2Vdc (ok) - Leitura de 1x Sinal Analógico 4...20mA de um transmissor de nível (ok) - Leitura da tensão da bateria que alimenta o hardware, para monitorar sua vida útil (bateria de 12V) (ok) - Leitura de 1x Sonda com protocolo Modbus RTU via RS-485 (ok) - Leitura de 1x Entrada digital para contagem de pulso (falta acrescentar) - Conectividade com internet via chip de telefonia móvel (de preferência 3G, mas pode ser GPRS) (ok) - Ter baixo consumo de energia para economizar a b...

Programação em arduino para que um robo com duas rodas com encoderes 580pps em cada volta e um rodizio dianteiro de apoio, ande perfeitamente em linha reta em uma distancia de pelo menos 4mts. Diametro da roda 65mm. Arduino Mega. Motores DC 12V. Drive L298N Deveria também ser capaz de após andar reto, fazer uma volta de 180º com uma roda. Então retornar em linha paralela a primeira. Podemos usar os encoders e o MPU6050. Froneço a pinagem pois ja tenho outros itens no projeto.

O freelancer tem que ter conhecimento de mecatrônica para Desenvolver esse projeto, pois devera desenvolver: 1 - Sistema de esteira motorizado, utilizando motor 12V; 2 - Projetar a esteira (e entregar o projeto do molde para injeção)

Desenhar 5 jogos de escovas automotivas em 3D, com a mesma textura das peças já existentes em nosso catálogo. Seguem (em “.pdf”) os 5 desenhos os quais necessito as imagens em 3D. Notar que a formação das peças são da seguinte forma: • BX-011-12V...........composto por 2 peças iguais • EVX-1-12V.............composto por 2 peças iguais • EVX-2-12V.............composto por 2 peças iguais • EVX-5.....................composto por 4 peças iguais • EVX-326.................composto por 4 peças iguais Adicionalmente estou anexando algumas imagens padrão confeccionadas para o nosso catálogo, para que se bas...

Possuo um laptop "Razer Blade" e preciso de uma bateria para substituir a original que foi danificada (a bateria não tem como ser reparada, precisa realmente ser trocada). Segue as especificações: NOTEBOOK - Razer Blade @ 2013 -Model No.: RZ09-0102 -Rated 19V === 7.9A -Product No.: 01021101 BATERIA - Li-ion Battery Voltage: DC 11.1V Capacity 6400mAh watt-hour rating: 71.04Wh Operating Temperature: 0ºC-45ºC A bateria tem que ser a padrão do notebook pois ela é interna e não externa. Segue em anexo fotos para mais detalhes. O QUE EU QUERO PARA O SERVIÇO: que encontrem onde a bateria poderá ser comprada, independente de ser em loja no Brasil ou exterior (website), mas que entregue em BRASÍ...

Por favor, Cadastre-se ou Faça Login para ver os detalhes.

Por favor, Cadastre-se ou Faça Login para ver os detalhes.

Preciso de um circuito, o qual será usado em computador. Eis suas configurações:  - Conectar 10 Leds e 1 Led strip a um mesmo sistema.  -- 8 Leds Brancos (1watt)  --2 Leds Vermelhos (1watt)  -- 1 Barra de Led Strip O circuito será temporizado, no seguinte ciclo:  -- A cada 20-30s acederá os dois leds vermelhos, e ficaram acesos por 1-2segundos. Log...seguinte ciclo:  -- A cada 20-30s acederá os dois leds vermelhos, e ficaram acesos por 1-2segundos. Logo quando apagar os leds vermelhos, acenderão os 8 leds brancos, juntamente com a barra Strip. É bem simples, mas tem que seguir esse tempos. Eu não tenho experiencia nesses tipos de sistemas, por isso, gostaria da placa do circuito conclu&...

...microchip to control multiple DC motors and MOSFETs, with integrated voltage regulation. This project requires expertise in high-power applications, voltage regulation, and serial communications. Project Requirements: Microcontroller: RP2040 chip to manage all operations. Power Handling: Board must handle input of 24V. Voltage Regulation: Conversion of 24V input to 12V and 5V outputs. MOSFETs: 5 MOSFETs for 24V, 7A control. 4 MOSFETs for 12V, 5A control. Communication: USB Type-C for robust serial communication. Inputs and Outputs: 2 analog inputs. 1 One Wire communication interface. Additional pins for digital input/output as required. Deliverables: Complete PCB design files ready for manufacturing, including gerber files. Schematic capturing and PCB layout. BOM (Bill ...

...involves utilizing both inputs/outputs and write a code in C language The project requires 7 inputs and 6 outputs. - Inputs : Time Temp sensor probe Soil moisture sensor VPD sensor PH sensor EC sensor Water level sensor - Output : 2 x Peristaltic pumps 2 x 12v pumps AC Fan (PWM-controlled EC-motor) 220v water motor pump (using Solid State Relay) inputs/outputs will need to be set up and configured and based on the reading of the input sensors the Microcontroller will control the outputs. The successful freelancer will need to provide the following : Full electronic diagram. List of the...

...встановлювати температуру через джойстик. Треба щоб значення температури регулювалась через PID-регулятор (програмно) для того щоб пристрої охолодження та нагріву змінювали потужність плавно в залежності від поточної температи. Список датчиків та деталей: 1. Датчик вологості та температури DHT11 (Є також bme 280) 2. Датчик газу MQ2 3. LCD1602 з i2c 4. Джойстик для ардуіно 5. Вентилятор 5v або 12v - для охолодження повітря (такий який в ПК встановлюється) 6. Нагрівальний елемент – лампа накалювання (не остаточний вибір) P.S. якщо треба щось ще чи краще використовувати іншу деталь - напишіть

Por favor, Cadastre-se ou Faça Login para ver os detalhes.

I’m looking to make a smart controller that can integrate with 12v compressors for inflating tires on off road vehicles. Mainly I need the the pcb and electronics designed and I can make the housing and everything else. If you would also want to design the housing in ok with that. Needs to be almost waterproof. Mainly splash proof and heat resistant. It will be mounted in the engine bay. As far as the controller goes all it need to be able to do is check pressure from a pressure sensor that will be connected in line from the compressor and control a 12v output source(5a at 12v) to trigger the compressor to turn on as well as for deflating need a valve to be controlled to air down to set pressure. Looking for keep it as simple as possible. Only gonna need about 4 ...

...original idea is starting from a existing CM4 carrier board ‘open source’, and modify it to add/remove elements, also ‘open source’. Most of the requirements can be found in any CM4 carrier board available with a public license, for exampe CMIO from raspberry pi. Description of the elements, interfaces and other requirements follows • Maximum board size 100mmx200mm aprox. • Power souce 12v, protected and converted to other DC (present in CMIO) • USB-C with mini USB conector for programming (present in CMIO) • USB 3.0 (present in CMIO) • Ethernet (present in CMIO) • CANBUS • PCIe (present in CMIO) • SD card slot (present in CMIO) • HDMI to LVDS signal + backlight &bu...

Hello there, I have a working Op Amp circuit that I would like to increase the output Gain from 2 to 4. I have +12v single supply, I have Schematic In Altium. Please Check attachment. Let me know if you can help.

I'm in immediate need of a well-experienced professional handling the setup and regulation of gas connections for industrial use. Skills and Experience needed: - In-depth understanding of industrial gas connections. - Proven experience in setting up and regulating gas connections. - Ability to work within a tight timeline. I encourage those interested in this project to specifically detail their relevant experience and expertise in their application. However, detailed project proposals are not strictly necessary at this stage. The key to success in this task lies in speed and efficiency without compromising safety and quality.

I'm seeking a skilled professional to work on the PCB design for a BLDC Stepper Motor. I want to create the smallest board (ideally 15mm x 30mm or less). The motor requires 12v, I'm hoping for the PCB to contain everything, and there could be a third button for speed or an FWD/rev switch and a pressure button for variable speed. I've been looking at the Attiny85 and L293D to drive the motor, but I'm happy to change that up to anything else.

I require a skilled Electronics Circuit Design Engineer to create a power amplifier circuit for me. The desired specifications for this project are as follows: - Input: +12v, -12v square wave (bipolar/monopolar) - Frequency Range: 0.1 Hz to 1000 Hz - Output: +100v, -100v - Load: 500 ohms - Output Current: 200mA Key requirements for this project: - Designing a power amplifier circuit that can handle the specified input and output voltage. - Ensuring the frequency range is between 0.1 Hz to 1000 Hz. - The output should be capable of driving a load of 500 ohms with 200mA output current. Skills and experience required: - Proven expertise in Electronics Circuit Design, particularly in designing power amplifiers. - Proficiency in managing both bipolar and monopolar input. - Soli...

I am looking for a skilled PCB designer to create a prototype that fits within a medium-sized, 2 to 4 inch space. This PCB should be tailored to contain an Arduino Mini and a 12V to 5V buck converter, with 3 pin and 2 pin JST GH connectors. The configuration of components on the PCB should follow a clustered arrangement to maximize space efficiency. This job does not require mass production capability at this time, with the primary focus being on creating a single prototype. Ideal candidates should have experience with Arduino components and compact PCB design.

I need assistance finishing a 12v circuit capable of effectively powering a LED light bar in a vehicle. Not ricer stuff, on an emergency vehicle. See attached diagram. Key job responsibilities include: - Designing a 12v circuit that fits my requirements - Adapting the design to the specific type of LED lights I use - Ensuring the configuration is optimized for 1-5 LED lights Ideal candidates should have: - Extensive knowledge of and experience with 12v circuits - Experience working with LED lighting systems - Strong problem-solving capabilities to troubleshoot potential issues and offer robust solutions - Excellent communication skills to explain the circuit design and any necessary precautions or maintenance tips. I value attention to detail and efficiency, so I w...

I am seeking an experienced electrical and HVAC engineer to design a comprehensive system for my large, 50+ feet house boat. This project involves designing an integrated electrical and HVAC system. Key requirements include: - A design that accommodates lighting, heating and cooling systems, and appliances. - Powering two 600 hp mercury engines on a 12v system with some low voltage lights. - Ability to utilize both shore power and independent power sources. Ideal qualifications: - Prior experience working with large boats/ships - Understanding of boat electrical and HVAC systems - Experience with multi-power source systems I look forward to enhancing the functionality and safety of my house boat with your expertise.

I need a highly skilled electrical engineer who can design an industrial-grade, slow-trickle charging circuit for lead-acid batteries. This device will be used primarily for powering backup syst...charging circuits for backup power systems. - Proficiency in using circuit simulation software. The final deliverable will include the circuit design diagram, a list of components needed, and comprehensive assembly instructions. I'm looking for someone who can provide a safe, reliable, and efficient charging solution for an industrial backup battery system. 18 numbers 12v Lead acid car battery Card power voltage (operating)- 12v DC Trigger Voltage -190v DC Stop Charging 216v DC the picture attached is of our present card used., We want to reduce cost and reliable. GRBL f...

...industrial use. Key Requirements: - Incorporating TI INA229 current and voltage sensing IC - Capable of handling up to 50 amps, 85V DC. - High durability for industrial use - All external connections to be via screw terminals (e.g. phoenix) and support the required current. - calculation of required parameters for INA229 register settings. - Size is flexible - Would be ideal if there was onboard 5V regulator for VIN of INA229, but open to this being external supply. Ideal Skills: - Strong background in PCB design - Experience with current and voltage sensing ICs - Knowledge of shunt resistor design and implementation - Understanding of industrial-grade PCB requirements If you are confident in your ability to deliver a high-quality, durable PCB design that meets these specifica...

I'm looking for an experienced individual who can proficiently integrate a 20V LED strip and a 12V pump into a singular circuit for my hydroponics setup. The key functions required for my hydroponics system include: am building a small, table top hydroponic system for use in a home. This circuit will require timed controls of an LED grow light and water pump ( + inputs from buttons in the future). The components I am using are: LED grow strip: rated at 20v, 350mA DC Water pump: 12v, 5W DC Timed controls: Arduino Uno (5min on/55min off Pump, 16h on/8h off LED) I have built a simple circuit for timed controls of the water pump. This comprises of 12DC input from a constant voltage (12v, 30W) plug and IRF520 MOSFET module for control of the water pump. The Arduino o...

I'm looking for an experienced individual who can proficiently integrate a 20V LED strip and a 12V pump into a singular circuit for my hydroponics setup. The key functions required for my hydroponics system include: am building a small, table top hydroponic system for use in a home. This circuit will require timed controls of an LED grow light and water pump ( + inputs from buttons in the future). The components I am using are: LED grow strip: rated at 20v, 350mA DC Water pump: 12v, 5W DC Timed controls: Arduino Uno (5min on/55min off Pump, 16h on/8h off LED) I have built a simple circuit for timed controls of the water pump. This comprises of 12DC input from a constant voltage (12v, 30W) plug and IRF520 MOSFET module for control of the water pump. The Arduino o...

I'm in need of a skilled electronics engineer with experience in power management circuits. Your ...a PMOS switch to disconnect if required. There are a number of key criteria that must be achieved and are non-negotiable. - The passive current of the total circuit should be as small as possible <50uA, currently over 1mA - The design needs to be triplicated (see schematic) - The three circuits must be completely independent of each other, not share components - The components must be rated for 12V and over, otherwise they can't be used - The design must specify all components required and their Digikey part numbers You can modify the existing circuit or produce a new circuit using discrete components or provide off the shelf solutions. All options considered if they m...

I'm seeking a skilled electronic engineer to design a 12V motion sensor alarm that's enhanced with a siren and key fob remote. This is a device focused on detecting movement with immediate effect as preferred. Key requirements include: - The alarm system gets activated instantly once motion is sensed. - The warning sound must be of a continuous alert type. A successful candidate will have proven experience in electronic engineering, specifically in designing and implementing sensor-based alarm systems. Familiarity with sound design is a plus. Commitment to time sensitivity and efficiency is essential. The chosen candidate should deliver a working prototype.

I am in search of an expert who can design and build a solenoid for me. The solenoid should be uniquely tailored to perform the following actions: - Pop up and down swiftly in a sequence of three times. - It should have the capability of a digital control for timed activations. - must be able to run on a 12v wiring for long periods of time - solanoid must be held firmly with plate. This unit should be housed in a container that is fully watertight, considering it will be used outdoors with potential exposure to wet conditions. The overall size of the unit must remain within the following dimensions: no longer than 300mm and no wider than 50mm in diameter. Ideal Skills and Experience: - Background in Mechanical or Electrical Engineering - Strong knowledge of digital timing contr...

Seeking an exceptional PCB designer to develop a power electronic voltage regulator. Deliverables must include four distinct output settings. The skill-set necessary for a successful undertaking will include a high level of knowledge in power electronic circuit configurations, specifically in voltage regulators, as well as prowess in detailed and precision-oriented multiple output design. - Required Skills: Power electronics, PCB design, Voltage regulators. - Experience: Proven track record with multi-output voltage regulator designs. - Output Specifications: Four unique voltage and current outputs. Specifics to be discussed after successful application.

More details: Which programming language are you more comfortable with? C# or Python or AI What is the level of under...details: Which programming language are you more comfortable with? C# or Python or AI What is the level of understanding or background do you have in the chosen programming language? Advanced What type of data are you looking to extract from the website? Contact information, Registration details, Company profiles The website: Is the regulator for estate agents in the UK. They hold information on al estate agents. I would like a script or console app r automated way (could be AI) of extracting all the UK estate agents from this website. I need their sector, address, phone number and name and website. Thank you

I'm looking for an experienced Electronics Engineer who can design a power supply circuit, specifically for charging devices. This project involves replacing a mechanical component, specifically a solid state regulator, with your innovative design. Skills and Experience Needed: • Solid understanding of power supply circuits • Experienced in electronics for charging devices • Familiarity with solid state regulators • Proven track record of successful circuit design The primary goal of this project is to create a reliable, efficient power supply circuit that can charge devices effectively. Please provide examples of similar projects you've completed in the past. Similar to attached file except 6 volt system and low side drive on field circuit. Runni...

I have a wiring diagram for my lighting system. Hardware I am using: - 3.3v to 5v Logic Level Converter Module - NE555 DC Delay Relay (5v version) - DC to DC 12v to 5v Step Down Converter Module (5v, 3a output) - WT32-ETH01 (running WLED) - Wago Connectors - 12v Power Supply I need you to assess my wiring diagram, tell me why it's not working as intended and tell me how to rewire it. I will then follow your instructions. You're required to work with me until it is working as intended. My level of knowledge in this department is low. I can solder etc, but when it comes to understanding wiring diagrams found online, it's beyond my level of knowledge, so I need someone to not only know where I've gone wrong, but to visualise what I need to do in easy-to-u...

I am looking for a skilled electrical or mechanical engineer to develop a 12v motor speed controller specifically for an industrial machine. This controller will primarily serve to regulate and adjust the motor speed as needed. The equipment is designed to function in an outdoor environment and hence, the controller's design should take into account factors such as weather conditions and robustness. Key Requirements: - Proficiency in electrical/mechanical engineering - Experience with 12v motor speed controllers - Knowledge of industrial machinery operation - Ability to design devices for harsh outdoor environments Considering the project's specifications, an engineer with a background in designing control systems for outdoor industrial equipment will be a perfe...

I need a skilled and experienced PCB designer who will focus specifically on product development for consumer electronics. This project involves a moderate level of complexity as it requires a standard multilayer PCB. The tasks expected to be conducted are as follows: - Mainly taking up PCB design tasks and ...circuit design An ideal freelancer would have prior experience working with PCB designs in the consumer electronics field. Expediency, precision and a keen eye for detail are vital as the developed prototype will directly contribute to a physical product. The project is a signal converter and i can attach a video of its funtion. Due to my limited software i need to add 2 more ICs: A voltage regulator and a bandpass filter at the highlighted area at the end of the attached vid...

...(except the antenna of the AIS, to be decided). The idea is starting from a existing CM4 carrier board ‘open source’, and modify it to add/remove elements, also ‘open source’. Most of the requirements can be found in any CM4 carrier board available with a public license. Description of the elements, interfaces and other requirements follows • Maximum board size 100mmx200mm • Power souce 12v • USB-C • Ethernet • CANBUS (Can provide design sources) • PCIe • SD card slot • LVDS signal + backlight (Can provide design sources) • Marine AIS class B (Can provide design sources) • Other UART inputs with optocouplers (to be decided) • GPS (Can provide design source...

I'm seeking a proficient PCB designer to develop a Wi-Fi rectenna design for the purpose of energy harvesting. The core requirements include: - Proficient skill set in PCB layout and design with a focus on rectenna structures - Understanding of the voltage multiplication to 5V to generate an output between 5V and 12V - Experience with wireless energy transfer, particularly in building Wi-Fi rectennas - Exceptional knowledge of rectifier topologies, specifically voltage multiplication The end goal is to have a Wi-Fi rectenna PCB that efficiently harvests wireless energy. Your expertise in harnessing this unconventional power source will position the project for success.

I'm seeking a skilled engineer to design a generator set powered by a 40 hp 1500 max rpm tractor's PTO. The design must be versatile, providing both DC for SMAW welding (9-48V, 10-500A) and AC power (15KW, 120 or 240V) for appliances. Required Features: - Utilization of an auto alternator or generator. - 12V or 24V battery system. - Digital or analog inverter - Some form of rheostat control for controlling welding amperage - Considerations for grounding and circuit breakers. - Peak performance at optimal rpms and comprehensive voltage regulation. - Off the shelf components highly desirable, so equipment specifications are more important than exact sourcing - Other than specifications for safe spacing of components, mechanical design is not required. Safety Features: - O...

I'm seeking a professional to develop a solar charge controller tailo...maximize the life and capacity of a lithium-ion battery, ensuring efficient energy use. - Light control: It should be programmed to automatically switch on the street lights at dusk and turn them off at dawn. - Overcharge protection: To prevent battery damage, the device should be designed to discontinue charging once the battery is full. - Voltage range: The gadget should function optimally at 12V. Ideal candidates should have experience in the development of solar charge controllers, electronics, power systems, or a related field. Proficiency in battery management techniques and light control systems is also vital. If you have significant experience in lithium-ion battery applications, it will be an a...

I am looking to have a DCC circuit breaker designed specifically for my model train setups. It must be rated for 12V and have the following features: - Overload Protection: The circuit breaker must safeguard against excessive current levels potentially damaging my model trains. - Short Circuit Protection: It's imperative that the breaker can disconnect circuits immediately upon detecting a short circuit. - Fault Detection: No mishaps should go unnoticed. The breaker should be able to identify faults in the circuit promptly. Due to the nature of my project revolving around miniature electronic equipment, an understanding and experience working on small-scale electronics would be ideal. A background in railway-oriented electronics would be a bonus, but not a necessity. Deep kno...

...should be included for setting the price of the product (including the option for a free price), 2. selecting the number of motors (1 to 10), 3. setting the number of stock items (1 to 1000), 4. Stock reset button. EEPROM Storage: User settings should be saved in EEPROM. Out of Stock Notification: The system should indicate when products are out of stock. Technical Specifications: Power Input: 12V DC/AC. Microcontroller: ESP or STM microcontroller with GSM connectivity. Communication: Internet connectivity for displaying live stock on a webpage. Deliverables: - Functional Embedded System: Development of the embedded system with all specified functionalities. - Documentation: Wiring diagrams, functional code and its explanations, and user instructions, troubleshooting meth...

...to this job. - The circuit is expected to operate on power input which could either be solar power or a 12v input. The provision for an optional standalone unit with 18560 batteries should also be included in the design. Hopefully using tp4056 - The selected designer is expected to possess a deep understanding and experience of power management, and preferably previous design experience of solar/18560 powered circuits. Circuit will include LDR, current limited using possibly Al5809 diode. Module will have 18 leds 6 red, 6 white, 6 amber selectable by means of plug pin or switch, using tp4056 so module could operate standalone or solar 6v cell added by means of plug or connected to 12v/24v dc supply. Module has selectable steady or flashing mode and can be operated with...

I am seeking a proficient designer/engineer to develop a Xenon Strobe Beacon with a specific focus on vehicle safety. This design + Gerber file + Layout + BOM will require: - Functionality for both indoor and outdoor use - Maximum visibility up to a short range of 100 meters By supplying 12V to PCB, Flash should be ON, 3 Flash per Second add temperature sensor

I am seeking an experienced electrical engineer to design a 12V battery charging circuit specifically for a lead-acid battery. The objective is to develop a design that is efficient and practical to implement. Key Requirements: -THE BUTTON PRESSED FROM THE OUTSIDE WILL PROVIDE 12V OUTPUT TO THE CARD - The input voltage for the charging circuit needs to be 24V. The successful candidate should have a proven track record in circuit design, particularly in chargers for lead-acid batteries. You should demonstrate understanding of safety requirements and efficiency metrics. Skills and Experience: - Expertise in Electronics and Circuit Design. - Understanding of lead-acid battery charging. - Familiarity with testing and validation proceedings. - Knowledge in PCB layout will be...

...development of a prototype with two main components: Aluminum Assembly: This component will be designed using CNC machines based on provided design ideas and images. Your tasks will include creating Solidworks 3D designs and executing prototype development. Light Fixture: Positioned above the moveable assembly, this fixture will include a red hazard light powered by a 5W system. It will feature a 12V 7AH lead-acid battery with specific charging and discharging times, along with a solar panel rated at 18V - 6.5W. Importantly, all components must be integrated within the assembly, and designed to withstand harsh weather conditions. Interested professionals are invited to submit proposals detailing: 1. Timeframe for prototype completion. 2. Approximate cost for the complete pro...

I'm looking for an experienced electronics circuit designer to help me with my home appliance. This project is centered around designing a functional electronic circuit that supports both task lighting and decorative lighting. To provide better detail: table top (no cable) task light small simple pcb (low batch of say 40 units) battery (rechargable) supply (12V LiFePO4) single MR16 7W cob lamp please see attached pdf It is ideal that the freelancer has good experience in electronics circuit design specifically for home appliances, and in the creation of circuits that support different lighting functionalities. The files would include Gerber files inc BOM.

Hey, I am looking for someone who will Design Hardware for ESP32 (Lighting with WS2815). I will do software by myself 1. Power Supply - Battery-operated - 2x18650 batteries connected in series - Ability to be powered by 12v (mains adapter) 2. StepUp to 12v for powering the programmable WS2815 LED strip (unless someone convinces me that it's better to use WS2813 with StepDown) - Power consumption for the LED strip, at least 50W, max ~200W - Logic level converter required from 3.3v -> 5v 3. StepDown for powering the ESP32 4. OLED display 128x64 I2C 5. Measurement of power supply voltage and power consumption 6. Power activation via a mechanical switch 7. 2x rotary encoder with button 8. Connector for programming the ESP32

Por favor, Cadastre-se ou Faça Login para ver os detalhes.

I am seeking a skilled electronics engineer with experience in automotive development to create a controller for inflating and deflating tyres on a 12V vehicle, specifically a car. The key requirements include: - Ability to autonomously control solenoids' opening and closing based on pre-set and adjustable pressure readings, with no manual interaction required. - Capability to accommodate various tire pressure readings for different driving conditions, such as off-road and high-speed highway settings. The ideal candidate will possess strong problem-solving skills and a demonstrated background in similar automation projects. Knowledge of automotive systems, particularly tyre pressure management, is essential. Familiarity with different driving conditions will also be benefici...

Hi guys I need a simple Arduino to able to do a launch control for four cyl motorbikes, trigger per button The rpm sensor is hall. Coils and injectors run 12v Need to able to set the gain (cut times) and amount of retard of the ignition, this is an idea if you have a optimal way let me know.

...of chat-input through the first 5 hours, getting help is hard work) To start simple lets go fot the following: A PT100 sensor + PCB that reads the sensor, sends the data from it into my Windows based C# (in Visual studio 2022) The flow of data should be: From PT100 Sensor (24V) -> M8 connector -> PCB -> M12 connector .> Ethernet -> POE Switch (48V) -> Ethernet PC -> C# code PCB: - Voltage regulator for DC - dual 4-20mA input from (24V) sensor - a minor CPU, that can send data in defined time loop And as we talked about Power through the etnernet - POE (48V) Sensors (24V) M12 connector for the Ethernet M8 for the Sensor IP67 Can handle ambient heat of -30 to +90 degree Corrosive resistant EMC - reistant If the IP on the network is then ask the server ...