Hobbyist / Arduino Uno Software - PHASE2
€30-250 EUR
Pago na entrega
Hello,
I am looking for a efficient programmer/electronics specialist to complete the following task/programming: --> PHASE 2 ONLY!!!
In a previous Step (PHASE1) this functions have been programmed and work fine --> Please have a look at the attached files and description of PHASE1 for your better understanding.
--Start of Description PHASE 1 --> This phase is completed already--
1 input button triggers the following activities:
5 modes --> Mode change after each button input from 0 (all off) to 1, 2, 3, 4, 5 and starts again from the beginning. Code stays in mode as long as there is no new button input
For each mode. It is required to have an easy to adjust set of parameters, for the following functions.
.) LED1 WS2812 Continuous animation for a 10W RGB PowerDot (animation/light effect must run smoothly as long as mode is not changed --> Effect Brightness/Speed/Animations style must be easy to adjust in final code)
.) LED2 WS2812 Continuous animation for a 60 pixel RGB ring (animation/light effect must run smoothly as long as mode is not changed --> Brightness/Speed/Animations style must be easy to adjust in final code)
There is a 4 channel relay switch connected to the Arduino
Set on/off --> 3 Channels --> depending on active mode (must be easy to adjust in final code)
Set on/off interval time (e.g 1sec on/30 sec off continuously repeating until new mode is selected) --> 1 of the 4 channels, depending on active mode (must be easy to adjust in final code)
There is a PWM motor connected to the Arduino --> Set RPM/or % individually for each of the 5 modes --> must be easy to adjust for each mode in the final code
A trigger mechanism via one of the Arduino pins to turn one device on/off (There must be a parameter to allow to set ON time in ms) --> The connected device is normally activated via a hardware button trough a short push and should in this setting now be activated/deactivated directly trough the Arduino. This must be again controllable for each mode and easy to modify
A mp3 Arduino sound module is connected and the Arduino should be able to trigger/start defined sound files based on events:
Arduino is turned on --> Starts a specific sound file from the attache Arduino sound module (files are stored on a sd card)
Change of mode --> (Starts a sound)
New mode activated --> (Starts a sound)
Arduino turned of --> (Starts a sound)
Sound files are available and will be played from the connected Arduino sound module (files are stored locally on a SD card)
We have a Programm that is able to do some of the described functions, but is still buggy, messy and not "user-friendly". It can be used, but I am also open to start from scratch.
--END of Description PHASE 1--> This phase is completed already--
The next step is PHASE 2 --> I am looking for a freelancer who is able to implement the following into my existing code.
The push button will only be needed to turn the Arduino on/off.
The mode change will be done via a RFID reader/chip.
A RFID Reader (AZDelivery RFID Kit RC522) is connected to the Arduino and based on the presented RFID chip the responding mode will be activated. CHIP 1 - Mode1, Chip2 - MODE2 etc. Chips could be presented in any order and Software must be able to activate the right mode.
If there is no RFID chip presented the Arduino will activate Mode 0 after a certain time.
The described is an initial part ONE of this hobby project, there are more steps planned once this is completed. I am looking for a reliable software/electronic freelancer.
ID do Projeto: #27596883
Sobre o projeto
24 freelancers estão ofertando em média €123 nesse trabalho
Hello I am experienced electronics engineer with more than 14 years of experience in PCB design and firmware development. I have designed a number of boards based on Arduino for different applications. I have read t Mais
Hi,Hope you are doing well! I’ve read and understood your project description about" ARDUINO EXPERT " Thanks for sharing your project requirement. It will be our great pleasure to work on your project. I have checked y Mais
Hello sir, I have experience in designing electronics circuits and can develop hardware compatible smartphone and PC based apps. I also have done a lot of IoT projects and can transform your idea into a fully working Mais
hello dear project owner i am an Electronics Engineer with experience in Embedded system designing and pcb designing i can do this in one day.
Dear Client I read the discription and I am interested in helping you to upgrade your device to phase 2, To complete this job I have enough of experience with "RFIds". I am electronics engineer from India with 4+ years Mais
Hi Sr, I was reading the .ino and .cpp files. I understand your description but not all the code, it is not an issue I can programming all that you need, maybe simplify it or organize on other way, we can see, because Mais
Welcome Sir I can help you in successfully completing your project. I am an expert in the Arduino field. I have done many similar projects for this work. Send me all the details. Here are some of my work I unveiled an Mais
Hi, I have more than 10 years of experience with programming microcontroller like PIC, AVR and ARM. I have also experience with programming Arduino which use an AVR microcontroller. I can help you with the modificatio Mais
hello sir.✋ I have just read your job description and your project is really interesting to me. The Items you raised are similar to what I have already done in practice and I think you can do it in a short time if you Mais
Hi Sir, I have gone through your description in which you are looking for Electrical Engineer having sound knowledge of Arduino microcontroller. I am highly interested to work with you. I always complete the project wi Mais
Hey there, I am Ali Raza and I have 4 years of experience in electronics project. I have read your job post and Understood that you want to complete your (PHASE 2). I would like to work for you to make your phase 2 li Mais
hello sir, hope you doing well. we are qualified and experienced PCB designer and embedded developers team where we design simple to hardest PCB development and firmware in Arduino and embedded systems using c/c++ and Mais
With my basic major in Electrical Engineering, I have had the opportunity to widen my knowledge in different fields. From Automation, Electronic, Programming to Signal Processing and Electrical Systems. I have deepened Mais
Hi, I'm Zsolt, a full time research engineer, working with Arduino and different sensor and actuator processing on a daily basis. I have also been involved in some Arduino freelance projects and had done some smart hom Mais
Hello. I'm an embedded systems developer spécialiste in arduino, I'll be glad to help you. I'm willing to help you in further advanced stages and phases if you need too. Feel free to accept my offer and contact me. Ha Mais
Hello, Respected Recruiter I have throughly read the project description. I am electronics graduate and proffessional embedded developer. I can perform those task as you mentioned in the description.
I have done countless projects with arduino cards and sensors for years. I can do this project for you after the project details
