Find Jobs
Hire Freelancers

AVR prog for heater controller

$30-250 USD

Concluído
Publicado há quase 6 anos

$30-250 USD

Pago na entrega
I have a project that I need help on. It's an on-demand heater controller, hopefully using an Adafruit AVR Pro Trinket or Arduino Pro Mini 328 (or similar small/cheap) dev board. Project info: 1) Circuit/code is bare bones: needs to read a 2-wire 56Kohm thermistor (have temp chart for the thermistor), output controls a single SSR (3v-32v input), no display needed. 2) 12vdc available and will add small dc/dc reg to drop voltage to power the controller. 3) GPIO output to control SSR (if nec, could run GPIO signal through very small mechanical relay): output high at or below low-setpoint, output low at or above high-setpoint. (we will also want a reverse function toggle in code, for future use). 4) Need top level code variables for easy adjustments to settings, including high-set-point (default 95C), and low-set-point (default 93C). No external buttons or other controls, all adjustments will be in the code (once we get it dialed, it will stay that way indefinitely). 5) would like to flash via OTS programmer dongle. I've got Atmel Studio and an AVRISPmkII, but could easily pick up USB or something else if needed. 6) the device must retain last setting/code between power cycles, must boot quickly. 7) function: apply 3V (or 5V) power to controller, controller boots and begins temp control routine, power off controller (there are other analog circuits that control everything else, including fail-safe issues). WE DO HAVE A SMALL BUDGET TO GET THIS DONE. The dollar amount posted is not a max. Qualified individuals please apply. Thank you!
ID do Projeto: 16897291

Sobre o projeto

2 propostas
Projeto remoto
Ativo há 6 anos

Quer ganhar algum dinheiro?

Benefícios de ofertar no Freelancer

Defina seu orçamento e seu prazo
Seja pago pelo seu trabalho
Descreva sua proposta
É grátis para se inscrever e fazer ofertas em trabalhos
Concedido a:
Avatar do Usuário
I have long experience with 8-bit and 32-bit micro-controllers. I work with PIC , AVR , ST and NXP micro-controllers. I use KEIL IDE , Atmel Studio and MPLABX IDE . I deliver tested , neat and well-commented code that can be reused or modified for future development. More to be discussed once you contact me . BR, M.T.
$55 USD em 3 dias
4,2 (5 avaliações)
3,2
3,2
2 freelancers estão ofertando em média $128 USD for esse trabalho
Avatar do Usuário
Hello I'm a controls engineer with tons of experience and can do the job Please contact me to discuss the project. Best regards, Dennis
$200 USD em 3 dias
4,7 (2 avaliações)
2,4
2,4

Sobre o cliente

Bandeira do(a) UNITED STATES
United States
0,0
0
Membro desde mai. 3, 2018

Verificação do Cliente

Obrigado! Te enviamos um link por e-mail para que você possa reivindicar seu crédito gratuito.
Algo deu errado ao enviar seu e-mail. Por favor, tente novamente.
Usuários Registrados Total de Trabalhos Publicados
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Carregando pré-visualização
Permissão concedida para Geolocalização.
Sua sessão expirou e você foi desconectado. Por favor, faça login novamente.